Keri-systems HPP-100 Uživatelský manuál Strana 7
- Strana / 48
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
HPP-100 Hand-Held Programmer
Revision 3.3 1
The HPP-100 Hand-Held Programmer
The
HPP-100 Hand-Held Programmer
is a powerful and convenient tool, yet its operation is
simple enough for anyone to master in a short period of time. The
HPP-100
has the appearance
of a TV remote control, but has a different principle of operation. It is a mini-transmitter using a
radio frequency (RF) rather than an infrared signal to transmit data. Unlike a television remote
control (that requires a direct line-of-sight between the infrared transmitter in the remote and the
infrared receiver in the television) the
HPP-100
should be held parallel to the proximity antenna
(see Figure 1).
Hand Held
Programmer
Reader
Figure 1 – HPP-100 Orientation
Hold the
HPP-100
within the range of the proximity antenna (approximately 1-foot) and press the
appropriate button to send a command. Allow about 0.5 seconds for a response from the reader.
Point it at the Master Control Reader (within three to four inches of the reader) and press the
appropriate button to send a command. Allow about a half-second for a command response. The
reader’s sound alert will respond to the command with a distinct beep.
Command Response “BEEP” Status
BEEP 1 short Confirms the depression of a key on the
Hand-Held Programmer.
BEEP-BEEP 2 short Confirms acceptance of a complete
command sequence.
BEEEEEEEEP 1 long Confirms rejection or an invalid operation was
attempted.
BEEP-BEEP-BEEP-BEEP continuous short Indicates the door sense switch is open.
- Keri Systems 1
- User Manual 1
- Hand-Held Programmer 1
- Contents 3
- Contents (continued) 3
- APPENDICES 36 4
- Revision 3.3 vi 5
- Hand Held 7
- Programmer 7
- Programming Command Groups 8
- System Preparation 9
- Setting a New PIN 11
- Configuring the Serial Port 12
- HPP-100 Hand-Held Programmer 13
- Revision 3.3 7 13
- Figure 3 - The PC Cable 13
- Figure 4 - The Modem Cable 13
- Command Descriptions 14
- Standard Commands 15
- Set the Unlock Time [N] 16
- Set the Held-Open Time [N] 16
- Card Management Functions 17
- Void a Card [G] 19
- Voiding Consecutive Cards [G] 20
- Change a Card’s Time Zone [N] 20
- Printing Functions 21
- Verify a Card [G] 21
- Print Transactions [G] 22
- Print Enrolled Cards [G] 22
- Print Status Information [G] 23
- Exit Command Mode [n/a] 26
- Define a Time Zone [G] 26
- Set Anti-Passback [N] 27
- Memory Module Functions 28
- Erase the Memory Module [n/a] 30
- Level Commands 31
- Security Functions 33
- Set Daylight Savings Time [G] 34
- Master Control Commands 40
- Clear Reader Memory [N] 41
- Appendices 42
- Revision 3.3 37 43
- Glossary 44
- Revision 3.3 39 45
- Revision 3.3 40 46
- Customer Support Information 47
- Warranty Information 48
Související produkty a manuály pro Hardware Keri-systems HPP-100
Hardware Keri-systems KWX-900 Uživatelský manuál
(14 stránky)
(14 stránky)
Hardware Keri-systems KWX-2.4 Uživatelský manuál
(14 stránky)
(14 stránky)
Hardware Keri-systems MS-1400 Uživatelský manuál
(7 stránky)
(7 stránky)
Ari-armaturen CONA S PN16-40 ES podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Ekwipunek Ari-armaturen CONA S PN16-40 ES.
Dostarczamy 1 pdf podręczników Ari-armaturen CONA S PN16-40 ES do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce